Lumped system model for elastic steel-concrete beams with partial interaction

Abstract

Purpose

The purpose of this paper is to introduce a numerical model to investigate static response of elastic steel-concrete beams. The numerical model is based on the lumped system with the combination of the transfer matrix and the analog beam methods (ABM). The beams are composed of an upper concrete slab and a lower steel beam, connected at the interface by shear transmitting studs. This type of beam is widely used in constructions especially for highway bridges. The static field and point transfer matrices for the element of the elastic composite beam are derived. The present model is verified and is applied to study the static response of elastic composite beams with intermediate conditions. The intermediate condition is considered as an elastic support with various values of stiffness. The elastic support can be considered rigid when the stiffness has very high values. The influence effect of shear stiffness between the upper slab and lower beam, and the end shear restraint on the static behavior of the composite beams is studied. In addition, the change in the stiffness of the elastic support is also highlighted.

Design/methodology/approach

The objective of this study is to introduce a numerical model based on lumped system to calculate the static performance of elastic composite bridge beams having intermediate elastic support by combining the ABM with the transfer matrix method (TMM). The developed model is applicable for studying static and dynamic responses of steel-concrete elastic composite beams with different end conditions taking into account the effect of partial shear interactions. The validity of the lumped mass model is checked by comparing its results with a distributed model and good agreements are achieved (Ellakany and Tablia, 2010).

Findings

A model based on the lumped system of the elastic composite steel-concrete bridge beam with intermediate elastic support under static load is presented. The model takes into consideration the effect of the end shear restraint together with the interaction between the upper slab and the lower beam. Combining the analogical beam method with the TMM and analyzing the behavior of the elastic composite beam in terms of shear studs and stiffness, the following outcomes can be drawn: end shear restraint and stiffness of the shear layer are the two main factors affecting the response of elastic composite beams in terms of both the deflection and the moments. Using end shear restraint reduces the deflection extensively by about 40 percent compared to if it is not used assuming that: there is no interaction between the upper slab and the lower beam and the beam is acting as simply supported. As long as the shear layer stiffness increases or interaction exists, the deflection decreases. This reduced rate in deflection is smaller in case of existence of end shear restraint. The effect of the end shear restraint is more prevailing on reducing the deflections in case of partial interactions. However, its effect completely diminishes in case of complete interaction. Presence of the end shear restraint and shear layer stiffness produces almost the same variations in the components of the bending moments of the composite beam. Finally, for a complete interaction, comparing the case of using end shear restraint or the case without it, the differences in the values of the deflections and moments are almost negligible.

Research limitations/implications

The following assumptions related to the theory of ABM: shear studs connecting both sub-beams are modeled as a thin shear layer, each sub-beam has the same vertical displacement and the shear deformation in the sub-beams is neglected.

Practical implications

The developed model can be effectively used for a quick estimation of the dynamic responses of elastic composite beams in real life rather than utilizing complicated numerical models.

Social implications

The applications of this model can be further extended for studying the behavior of complex bridge beams that will guarantee the safety of the public in a quick view.

Originality/value

Previous models combined the TMM with the ABM for studying the static and free-vibration behaviors of elastic composite beams assuming that the field element is subjected to a distributed load. To study the dynamic response of elastic composite beams subjected to different moving loads using transfer matrix ABM, it was essential to use a massless field element and concentrate the own weight of the beam at the point element. This model is considered a first step for studying the impact factors of elastic composite beams subjected to moving loads.

Citation

Ellakany, A.M., Ali, M., El-Gohary, M.A. and Elkholy, M. (2020), "Lumped system model for elastic steel-concrete beams with partial interaction", Multidiscipline Modeling in Materials and Structures, Vol. 16 No. 1, pp. 121-133. https://doi.org/10.1108/MMMS-01-2019-0007